Skip to content

Flare nut torque chart (N·m) for R32 split air conditioning

This flare nut torque chart gives 13.7 to 18 N·m for a 1/4 inch nut and 32 to 42 N·m for 3/8 inch. Mitsubishi Electric wants more on 5/8 inch. The Wera 9530 is the torque wrench that reaches every nut.

By Westbridge Air Team · Updated 4 November 2026

Torque wrench on a flare nut with a backing spanner holding the brass service valve of an outdoor unit, copper pipe below
1/4 in nut, three makers
13.7 to 18 N·m
Mitsubishi Electric 5/8 in
73.5 to 78.4 N·m
torque wrenches ranked
3
On this page10 sections

Flare nut torque chart (N·m) by maker and pipe size

Each column is one maker's figure from one R32 manual.

Pipe sizeNut spannerDaikinMitsubishi ElectricFujitsu
1/4 in (6.35 mm)17 mm15 to 1713.7 to 17.716 to 18
3/8 in (9.52 mm)22 mm33 to 3934.3 to 41.232 to 42
1/2 in (12.7 mm)26 mm50 to 6049.0 to 56.449 to 61
5/8 in (15.88 mm)29 mm63 to 7573.5 to 78.463 to 75
3/4 in (19.05 mm)Not listedNot listedNot listed90 to 110

Sources: Daikin; Mitsubishi Electric, also the nut sizes; Fujitsu.

Flare torque: where the oil goes, and how far the pipe sticks out

Cut-away of a flare joint showing oil on the 45 degree flare face only and dry threads, and a pipe set 0 to 0.5 mm above the flaring bar for an R32 clutch tool
Oil on the flare face only, and the pipe height above the bar.

Best flare nut torque wrench: our top 3 ranked

Tap a button to re-rank the wrenches by what matters most to you.

Winner by category
Rank by
  1. Our top pick
    1
    Best overall

    Wera 9530

    £405.95 at Tooled-Up

    Overall 8.0 out of 10, Very good
    Reaches every nut
    Reaches every nut: 10
    Value for money
    Value for money: 5
    Easy to use
    Easy to use: 9
    Built to last
    Built to last: 8

    Reasons to buy

    • Goes up to 100 N·m
    • Reaches every nut in the chart
    • Adjustable jaws, so one tool

    Think twice if

    • Four times the price of the others
  2. 2
    Best value

    Mastercool 70078

    £93.21 at Aircon Spares

    Overall 7.5 out of 10, Very good
    Reaches every nut
    Reaches every nut: 7
    Value for money
    Value for money: 9
    Easy to use
    Easy to use: 7
    Built to last
    Built to last: 7

    Reasons to buy

    • Cheapest set here
    • Goes up to 75 N·m

    Think twice if

    • Mitsubishi 5/8 in only at its top
    • On back order
  3. 3
    Fine for Daikin

    Rothenberger 175001

    £99.60 at Tester.co.uk

    Overall 6.5 out of 10, Good
    Reaches every nut
    Reaches every nut: 5
    Value for money
    Value for money: 7
    Easy to use
    Easy to use: 7
    Built to last
    Built to last: 7

    Reasons to buy

    • Covers 17 to 29 mm nuts
    • Fine up to 5/8 in on Daikin

    Think twice if

    • Stops at 70 N·m
    • Too low for Mitsubishi 5/8 in

Scores are our judgement from each maker's specs, UK prices on 28 October 2026 and what technicians say online. We have not tested these wrenches ourselves.

How tight should flare fittings be?

Use a torque wrench and the range in your unit's manual. These settings fit all three makers:

  • 1/4 in: 16 or 17 N·m.
  • 3/8 in: 34.3 to 39 N·m.
  • 5/8 in: 73.5 to 75 N·m. Check the manual.
  • Too tight: Mitsubishi Electric warns an over-tight nut may crack and leak (Mitsubishi Electric). Too loose: the flare will not seal.
  • Threads: Mitsubishi Electric says keep oil off them, as it leads to too much torque.
  • Flare face: Daikin says ether or ester oil, not mineral oil (Daikin).

Flare torque wrench: highest setting compared

Mitsubishi Electric 5/8 inch nuts need at least 73.5 N·m.

Higher is betterHighest setting, N·m
  • Rothenberger 17500170
  • Mastercool 7007875
  • Wera 9530Best100
Makers' listings, checked 28 October 2026.

Flare nut torque wrench at a glance

WrenchBest forPriceOur score
Wera 9530Every make, every nut£4068.0 / 10
Mastercool 70078Tight budgets£937.5 / 10
Rothenberger 175001Daikin, and Fujitsu to 5/8 in£1006.5 / 10

R32 flare nut torque: is it different?

No. All three manuals in the chart are for R32 units. Daikin's newer ATXD manual gives the same 1/4 and 3/8 inch figures (Daikin ATXD).

What changes is the flare. Use soft copper only (Daikin FTXJ). Our best flaring tool guide ranks the tools.

Mitsubishi flare nut torque specs vs Daikin and Fujitsu

Mitsubishi wants more on 5/8 inch, at 73.5 to 78.4 N·m (Mitsubishi Electric). It asks a little less on 1/4 inch.

Flare torque wrench reviews: what technicians actually say

These are technicians on Reddit, found through Google UK search.

  • "you should always be using a torque wrench on mini splits"
  • A Hilmor wrench "doesn't even adjust big enough for most Mitsubishi nuts"
  • Nylog on the threads "will make it easier to over-torque"

Flare nut torque chart: FAQ

How to torque a flare nut?

Turn the nut on by hand first, three or four turns in Daikin's manual. Hold the valve or fitting still with a second spanner. Then tighten with a torque wrench to the figure in the unit's manual.

Torque specs for 1/4 flare nut?

A 1/4 inch flare nut takes 15 to 17 N·m on Daikin, 13.7 to 17.7 N·m on Mitsubishi Electric and 16 to 18 N·m on Fujitsu R32 splits. A setting of 16 or 17 N·m fits all three.

Torque specs for 3/8 flare nut?

A 3/8 inch flare nut takes 33 to 39 N·m on Daikin, 34.3 to 41.2 N·m on Mitsubishi Electric and 32 to 42 N·m on Fujitsu. Anything from 34.3 to 39 N·m fits all three makers.

Sources

10
  1. Daikin: R32 split installer reference guide 4P513661-7E (ARXM, RXM, RXA, RXF, RXJ)
  2. Daikin: ATXD25/35A R32 indoor unit installation manual 3P748643-4P
  3. Daikin: FTXJ-MW installation manual 3PEN482320-15Z
  4. Mitsubishi Electric UK library: MSZ-LN18 to 60VG2 installation manual
  5. Fujitsu (General Inc.): R32 wall mounted installation manual 9387848007
  6. Google UK snippets: flare torque wrench threads on Reddit
  7. Rothenberger: torque fork wrench set 175001
  8. Tester.co.uk: Rothenberger 175001 torque spanner set
  9. Aircon Spares: Mastercool 70078 torque wrench kit
  10. Tooled-Up: Wera 9530 torque wrench set for heat pumps and air conditioning